​Hydroxypropyl Methyl Cellulose HPMC-manufacture,factory,supplier from China

Raw material of Particle board.1.Particleboard is made on the basis of scrap materials, but the range of scrap materials is relatively wide. According to different types of scrap materials, particleboard can be divided into wood particleboard, bagasse particleboard, flax chipboard, cotton stalk particleboard, Bamboo particle board, etc., cement particle board, gypsum particle board. It can be seen that most of the scraps contain wood cellulose.

What is OSB ?Oriented Strand Board (OSB) is a kind of fresh wood with large diameter and straight trunk as raw material. It is processed along the direction of wood grain by special slicing processing equipment.

Oriented Strand Board Introduction:Oriented strand board (OSB), also called European pine board, is made of small diameter wood, interfelled wood, wood core, board veneer, branch Y wood, etc., and processed into 90-130mm long, 5-30mm wide and 0.5mm thick strands in the direction of wood grain by special planing equipment (long wood planer or two-stage chipping planing equipment), then dried, glued, and formed in the prescribed direction by hot pressing.

    Oriented strand board (OSB), also known as Ozon board, originated in the 1970s and developed from structural particle board-waffle board. Since the mid-1980s, it has developed rapidly in North America and Europe, and has begun to replace plywood in large quantities. For use with fiberboard.    Oriented strand board is a new type of high-strength environmental protection board.

Characteristics of OSB1. Wide sources of raw materials and low prices.The raw materials of directional particle board are mainly small diameter wood of soft coniferous wood and broad-leaf wood, fast-growing thinning forest, such as eucalyptus, Chinese fir, poplar thinning wood, etc., with a wide range of sources.2. High output rateCompared with other types of wood-based boards, oriented particle board has a higher output rate.

   The production of chipboard in China has gone through a repeated process from the rise in the 1980s to the decline in the 1990s and then to the rise again in 2000. After the particle board was abandoned by the market due to poor quality and other reasons, many particle board enterprises learned a lesson, introduced advanced production lines from abroad and improved the technology level.    After that, the quality of particle board in China has improved significantly, and it has been accepted by the market again.

     Particleboard, also known as chipboard, is a wood-based panel that is made of wood or other lignocellulosic materials and glued under heat and pressure after applying an adhesive.

      Density board is called density fiberboard. It is made of wood fiber or other plant fiber, prepared by fiber, applied with synthetic resin, and pressed under heat and pressure.     According to its density, it can be divided into high-density fiberboard, medium-density fiberboard and low-density fiberboard.

The raw materials for making particleboard include wood or wood fiber materials, adhesives and additives. The former accounts for more than 90% of the dry weight of the board. The wood raw materials are mostly taken from felled wood in the forest area, small diameter wood (usually less than 8 cm in diameter), felling residues and wood processing residues. Wood chips, shavings, wood filaments, sawdust, etc. processed into flakes, strips, needles and granules are called chips.

Manufacturing Process Broadcast1. Chipping: It is the manufacturing workshop of the raw materials in the whole board production. It mainly cuts loose wood into wood chips that meet the production specifications, so as to provide better conditions for fiber separation in preparation for heat.2. Thermal grinding. The wood chips cut out of the chipping workshop are preheated and cooked, and then mechanically separated to obtain fibers.3. Fiber drying: heat grinding and sizing to make the moisture content of the fiber reach 40%-50%.

     It is said that wall panels originated in England in the 16th century. Everyone knows that the climate in England is cold and humid. In order to block the damp and cold lower part of the wall, wall panels are used for insulation.    Another theory goes back to the Netherlands in 1300. At that time, Europe was in the dark Middle Ages, and knights wearing armor and holding long swords often scratched the walls of castles or palaces inadvertently. Protect with wood.     At the beginning, wall panels were mainly used in castles and palaces.

      The Invention of Wood-based Panels     The invention of wood-based panels can be traced back to 3000 BC. At the beginning of the 1st century BC, the Romans were already familiar with veneer manufacturing technology and plywood manufacturing principles.     In 1812, the French invented the veneer sawing machine.     In 1834, France issued a planer patent.     After 1844, the improved rotary cutting machine was officially used in industrial production.

App Features:Because of the three-layer criss-cross structure, Ozon board is more uniform than ordinary particle board, has better toughness, strong nail holding power, and is not easy to swell when it is damp. It is used as a house structure abroad and is strong. But it is relatively thick, the surface is uneven and difficult to handle, and it is rarely made into furniture.  When Ozon board came to China, it has almost become an upgraded substitute of large core board, with good quality and high price. It is especially suitable for the base layer of the background wall.

Advantages of Carbon Crystal Plates or Black MDFCarbon crystal panels are environmentally friendly, durable, moisture-proof, flame-retardant, sound-absorbing, anti-aging and other practical and excellent features, helping you easily have a healthy, environmentally friendly and safe living home.Noise reductionThe carbon crystal wall panel has a good diffuse reflection for sound, and has a relatively buffering impact of the subwoofer; the sound insulation has reached 29 decibels after testing, which is 13 decibels higher than the sound insulation of a 25 cm wall, which solves the incoming noise

Moistureproof board is to add a certain proportion of moistureproof particles in the production process of the base material, also known as melamine board (base material), which can greatly reduce the degree of expansion of the board when encountering water.  Gaotang County Xinhua Wood Industry Co., Ltd. was established in April 2010 with a registered capital of 11 million yuan. It covers an area of about 76,600 square meters, including a construction area of about 22,000 square meters.

  1. The characteristics of density board: the surface of density board is smooth and flat, the material is fine and dense, the performance is stable, the edge is firm, and the surface of the board is decorative. However, density boards have poor moisture resistance, and in comparison, density boards have poorer nail-holding power than particle boards. If the screws loosen after tightening, it is difficult to fix them again due to the low strength of density boards.2. The use of MDF: mainly used for laminate flooring, door panels, partition walls, furniture, etc.

Product performance  The most advanced flat pressing production line in the world. Therefore, the physical performance is higher and better than that of MDF. Its density is usually above 800kg/M3. The high-density fiberboard produced has reached 930kg/M3, which has reached the advanced level of similar products in Europe and America.   The board surface texture is fine and smooth.

Carbon crystal panels have many advantages, including:1. Strong durability: carbon crystal plate has the characteristics of high strength and wear resistance, and can maintain its original performance and appearance in long-term use.2. Ultra-thin and light: the carbon crystal plate is very thin and light in weight, which can reduce the weight of the overall decoration material, and is also easier to transport and install.3.

    Medium density fiberboard is a kind of artificial board made from the thinned wood of branches, small diameter wood, fast-growing wood, bamboo and other plant materials with limited wood resources. The comprehensive utilization rate of wood is high, which conforms to China's forestry development policy and is conducive to the implementation of China's forestry sustainable development strategy.Medium density fiberboard DisplayProduct Certificates-SGS,ISO9001,FSC  

Particleboard Quality Judgment1. From the appearance point of view, look at the size and shape of the wood chips in the center of the cross-section. The length is generally 5-10MM in length. If the length is too long, the structure is loose, and if it is too short, the deformation resistance is poor, and the so-called static bending strength does not meet the standard;2. The moisture resistance of wood-based panels depends on its density and moisture-proof agent.

An Introduction to OSB Board      OSB is Oriented Strand Board ,the upgrading of traditional particle board.

   Density board, also known as fiberboard, is an artificial board made of wood fiber or other plant fiber by hot pressing after slicing, cooking, fiber separation, and drying, then applying urea-formaldehyde resin or other suitable adhesives. the   According to the density, it can be divided into low-density board (weight less than 550KG/M3), also known as low-density fiberboard. Medium density board (weight 550~880KG/M3), also known as medium density fiberboard.

     Density board is called medium density fiberboard（MDF) . It is made of wood fiber or other plant fiber, prepared by fiber, applied with synthetic resin, and pressed under heat and pressure. According to its density, it can be divided into high-density fiberboard, medium-density fiberboard and low-density fiberboard. It is widely used in the fields of furniture manufacturing and decoration in China.Xinhua Wood Show  Xinhua Wood Machinery  Gaotang County Xinhua Wood Industry Co., Ltd.

Advantages of carbon crystal panels in customized home furnishing The carbon crystal plate is made of a PVC film on the base material. The veneer can not only play a decorative role, but also protect the inside of the plate from external erosion, replacing the position of the paint. Therefore, the carbon crystal plate is used in There is no need to paint at all times, which is very convenient and trouble-free.